Engine Mounts - 4x4 Off-Road UTV Build Ep.19
22:04
833,558
Reddit
Fabricating mounts for engine, differential and tow hitch.
This is part of a series of a four wheel drive utility vehicle build to lessen the work load on my trusty 2002 Honda Foreman Rubicon TRX500FA. This partially answers the question "Why?" but for those who want to ask "why don't you just buy a side-by-side instead of building one?" I just want to say - I'm not made of money. Side-by-sides are ridiculously expensive, even the car I drive around daily is worth less (not worthless though!), hell, it is even worth less than my 2002 Honda ATV.
"How much HP will it have?" - the 1.4 litre FWD petrol engine I'm planning on using has 55 kw and this will not change, but the torque will be tripled via the BMW differentials I'm using to transfer power to front and rear axles.
"It will be too heavy!" - this project just like the firewood processor project does not have to float. And a heavier vehicle will handle better anyway when hauling heavy loads.
Stay tuned for future episodes! Thanks for watching!
My other videos: svsoft.info
#donndiy #homemade #4x4
Soundtrack:
Pomade - Silent Partner (SVsoft Audio Library)
Welding equipment borrowed from Spetselektroodi AS, Estonia:
Fronius TransSteel 2700 welder
Optrel Crystal 2.0 Welding Helmet
Hypertherm Powermax 45 XP plasma cutter

Kommentarer
  • Donn DIY
    Donn DIY

    More fabrication videos on svsoft.infovideos

    • Fernan du
      Fernan du

      What kind of gas you use for the mig soda maker

    • Serkan Ceylan
      Serkan Ceylan

      I'm waiting for a series of videos. You throw it too late.

  • Ринат Гарифулин
    Ринат Гарифулин

    0:53 Насвистываешь пятую симфонию Бетховена😊

  • Assistor _M
    Assistor _M

    Ilusti toimetad, hea garaaž. Edu 😁

  • Fred Wilson
    Fred Wilson

    You have mad skills,knowledge,and tools

    • Donn DIY
      Donn DIY

      Cheers mate!

  • DoctorWhoRoblox1935
    DoctorWhoRoblox1935

    If I were you I think I prefer to have the drivetrain suspended from the body like the wheels but that too may be troublesome. Uh... I don't know.

  • Valter Ventura
    Valter Ventura

    Top👍👍

  • webcarros 0721
    webcarros 0721

    Vai ficar show 👏🏼👏🏼👏🏼👏🏼👍🏼

  • A K
    A K

    Hi from other side of planet

  • red king
    red king

    I am iranian

  • red king
    red king

    دربوزت حاجی خیلی مردی

  • OFRA Corp
    OFRA Corp

    Hello, like a pro ! very good job.

  • WELDER OF MASTER
    WELDER OF MASTER

    Good videos tutorial next time

  • Angga Rilan Pratama Angga
    Angga Rilan Pratama Angga

    👍👍👍

  • Oerknalx
    Oerknalx

    Look nice as hell my dude ! Keep up the amazing work !

  • Eren Kocbey
    Eren Kocbey

    Probably you dont like that reinforcement for mounts and you are gonna change that later. lol.

  • Terry J
    Terry J

    So many other drivetrains, out there. I would have picked one that doesn't need to be a passenger. Where do your friends get to sit? Under the hood? In back? On the motor? No friends?

  • Юрий Макаров
    Юрий Макаров

    У меня шов получается плохой когда магнит рядом 2:18 Варю тоже полуавтоматом.

  • Alberto Costea
    Alberto Costea

    Very interesting, cool content!!

  • Wacek Vaginiarz
    Wacek Vaginiarz

    Engine?

  • Oklahoma Preppers
    Oklahoma Preppers

    You make it look simple

  • Off Road Adventures Greece
    Off Road Adventures Greece

    My friend you are are doing amazing job👍👍👍👍

  • qualifier one
    qualifier one

    Jõudu tööle!

  • Anibal Peña
    Anibal Peña

    No me canso de ver el video y el trabajo realizado con la cortadora de plasma, es perfecto!!!!!! Felicidades!!!!!!!!!

  • thorn vannak
    thorn vannak

    good

  • Kacper Ilczuk
    Kacper Ilczuk

    When you start painting all the steel parts?

  • Alex Eat-Sand
    Alex Eat-Sand

    everything fits like a glove

  • Alex Eat-Sand
    Alex Eat-Sand

    watching him welding is so satisfying

  • Criadero Manzanarez
    Criadero Manzanarez

    Air box filter with snorkel capabilities for sure!

  • pakmude crew
    pakmude crew

    Good konten bro Engine mounts 4*4 installed

  • Cellphone Shop
    Cellphone Shop

    Good job Brow

  • Kearin vg
    Kearin vg

    Good 👍👍

  • Tony Urquhart
    Tony Urquhart

    i would go with the 1.9 Air Box...

  • Marcos henrique peres Peres
    Marcos henrique peres Peres

    PARABENS PELO carro Legal. Tô gostando muito .PARABENS....

  • MLG
    MLG

    Отличная работа ! Привет из России 👍

  • Александр Петраков
    Александр Петраков

    К сожалению не на каждом заводе такое качество, красавчик !

  • Pauli Puhakka
    Pauli Puhakka

    Awesome build man, look like it's going to be a fun ride. Good job man👍🇨🇦

  • willys48
    willys48

    Nice work. The quality of your work and attention to detail improves with every build. For ease of changing the air filter I would go with the 1.9 airbox. Fording capability never has been a huge concern for me. My intolerance for being cold and wet is usually far less than the capability of the jeeps and utvs I have driven. 😆

  • Paweł Mikołajuw
    Paweł Mikołajuw

    Tylko czekam na następny odcinek, good luck!!

  • Joseph OLDHAM
    Joseph OLDHAM

    Very good job 👌🇵🇫

  • Wayne Crews
    Wayne Crews

    Your fabrication is on a higher level than most of SVsoft. 👍🏻👍🏻👍🏻 The engine appears the be a little “loose” with just those 3 mounts. Hopefully it holds up or you can find a set of holes to add a 4th mount to “tighten” it up a bit. Looks like the 1.9 airbox has a bigger filter so if you can make it work with the gas engine within the chassis then that would be my choice

  • Путь Жизни Металлиста
    Путь Жизни Металлиста

    Плазма отличная штука для таких дел !

  • motoyarik
    motoyarik

    Странный трактор получается...

  • Владимир Володин
    Владимир Володин

    Take a video about this , at least something in your life will do global satanic elite it consists of around 10,000 people , from well-known Merkel , Sarkozy, bill gates , Zuckerberg , Sergey Bryl and Larry page , the Bush family, the Clintons , Rockefellers , Rothschild, Baruch,Leiba, Morgan, Carnegie , almost all Royal and Imperial families from around the world and many other names .They are behind the world wars, they created and spread the coronavirus, the main goal is to ensure the arrival of the Antichrist and prevent the second coming of Jesus and the last judgment , such conditions are allowed by God, because before destroying Lucifer (iblis),because he disobeyed God and did not worship Adam , he asked not to kill him, to leave him alive, and for this he will experience the creation of God - man in particular and humanity in general, Lucifer(iblis) . For mankind there are 3 options for the outcome of the first coming of Antichrist and the fall spirit that it has not been rewarded with the 2nd coming of Jesus and then judgment will not, and will all be erased in the dust , except for the approximate 190.000 people who helped the devil to defeat the mankind and the Second variant of the Human spirit on a global scale will be such strong that will not work with them to bring the Antichrist , and will have 2 coming of Jesus and then there will be judgment . Well, the last option they will achieve the coming of the Antichrist , but humanity in general will fight for itself and God will let down Jesus and we will win and there will be a last judgment .They are fighting for eternal life for themselves, and for us they want to leave the option that we will all be wiped out and not even bother with the last judgment . The outcome depends on each of you , and your life after death .This is the information you need to know why Satanic is actually doing all this .And our task is to stop them . And let me remind you that the world is developed by industrialists , scientists , farmers , teachers, well, no matter how satanists, they have always slowed down industrial progress

  • Josh Ward
    Josh Ward

    Keep up the good work!

  • Вовка Псих
    Вовка Псих

    Good lake from you hobby. I am dont not speak englich . I lok you mehanical simphony. Verry verry positive and creative ingeneering idea.

  • 504 Owner Official
    504 Owner Official

    oww good work

  • Геннадий Михайлович
    Геннадий Михайлович

    А оборудование супер

  • Геннадий Михайлович
    Геннадий Михайлович

    Жесть!

  • Janne Kokko
    Janne Kokko

    Hyvää työtä! :)

  • Алексей Л
    Алексей Л

    Болтовые соединения сквозь профиль держать не буду. Очень быстро ослабнут из-за деформации профильной трубы. Надо во все такие места внутрь вставки трубчатые делать.

  • Simon Church
    Simon Church

    Well that looks easy, I’ll order a welding torch beginners kit from eBay lol

  • AI 43
    AI 43

    Good job! Go with the Diesel filter.

  • george psilos
    george psilos

    Very nice build. In my opinion use the 1.4 air filter box, it is sturdier and it can be sealed easily with the screws and a rubber gasket. P.S. I think that you should check the engine oil leak above the steering wheel pump. Keep up the good work

  • 趙木成
    趙木成

    Your technique is so good that it has been observed for a long time. (Even if I am still an expert in turning) also produces serious self-doubt.

  • Олександр Вовк
    Олександр Вовк

    Вподобайка

  • ludwik95
    ludwik95

    9:14 Renault? 😅

  • Thắng Nguyễn
    Thắng Nguyễn

    Dang cap....!

  • Lou Adzima
    Lou Adzima

    Looks like your plasma has already paid for itself.

  • baby bash
    baby bash

    Nice welding first time i see a guy that build something and does a clean weld

  • martin puricelli
    martin puricelli

    Use both air cleaner box, in serial layout. its an offroad. Asome job you are doing

  • andre dionne
    andre dionne

    d abonner trop d annonces et de commerciaux

  • MARANI MARCO
    MARANI MARCO

    🦾🦾🦾🦾🇮🇹

  • Alex Mos
    Alex Mos

    Лайкос 👍👍👍

  • Николай Остапченко
    Николай Остапченко

    Это железо для теплиц плохо подходит , а для техники типа спорт инвентаря вопще не как.

  • Джамалутдин Каллаев
    Джамалутдин Каллаев

    😘

  • Игорь Мищенчук
    Игорь Мищенчук

    Здравствуй только круглое отверстие облегчит конструкцию но не уменьшит прочность

  • Eduardo Resio Pesca en Argentina
    Eduardo Resio Pesca en Argentina

    nice work!!!!

    • Donn DIY
      Donn DIY

      Cheers man!

  • Marty V
    Marty V

    Awesome as ever! Nice to see the CNC plasma come in handy now 👍🍻

    • Donn DIY
      Donn DIY

      That CNC is really great for sure. 🤘

  • martin gardener
    martin gardener

    Build is coming on well but I think I would have kept the diff rubber mounts to absorb some of the shock load. I think from the video you are maybe In two minds about the solid mount too!

    • martin gardener
      martin gardener

      @Donn DIY I wasn't thinking so much of vibration more shock if say the clutch was let out a bit too sharp but that would probably put more stress on the front mount really. Anyway enjoying your build.

    • Donn DIY
      Donn DIY

      I've seen other rimilar ATV build and they've all solid mounted the diffs. The speeds will be low and the cabin is not enclosed so the vibrations that one could hear will be minimal.

  • Didzis Reiznieks
    Didzis Reiznieks

    Good work 👍

  • der MICHL
    der MICHL

    Donn, i follow you 2 Years. Nice work, nice Projects. And you need a DIY Sandblaster ;) Greetings from Bavaria

    • der MICHL
      der MICHL

      @Donn DIY Do you need a "Battleplan"?

    • Donn DIY
      Donn DIY

      Yes, I do need a sandblaster. 😉

  • Anton Solovev
    Anton Solovev

    Please make subtitles in Russian

  • Anton Solovev
    Anton Solovev

    У тебя токарный СССР, так что давай субтитры на русском))

  • Anton Solovev
    Anton Solovev

    Мне бы такие tools)))

  • Anton Solovev
    Anton Solovev

    Я тоже так хочуууууу...

  • Albius Wan
    Albius Wan

    norm.....good device

  • Robert Manley
    Robert Manley

    I would have to say that I like the round air box cleaner better. Looks like it will fit your configuration a lot better. Excellent work !! That plasma table is really getting a workover it works very nice on the thick stuff as well !! I love this build !! One of a kind and custom !!👍👍

  • Bernd Odin81
    Bernd Odin81

    👍👍👍🔝👋👋👋🤝🤝🤝🇩🇪

  • avery intrusive
    avery intrusive

    Careful with the coolant system even a small leak at operating temperature will change your life. Love the build.

  • L P
    L P

    I really like Donn's work, he is an excellent fabricator. However, I feel the videos are becoming too reliant in the use of the plasma cutting table. I liked it more when he did his cutting and welding like most of us at home. Best of luck Donn.

    • L P
      L P

      @Donn DIY thanks for the reply. Good to hear from you, keep up the good work!

    • Donn DIY
      Donn DIY

      No worries. The angle grinder is still my main tool. I'm using the CNC to learn it more in depth and second - I wan't to create a set of blueprints other people can use for building their own 4x4 tractor buggy.

  • Werner Gratsch
    Werner Gratsch

    Do you have Fronius Welder or didnt i see it right?

    • Donn DIY
      Donn DIY

      Yep, I'm using Fronius TransSteel 2700

  • Job38 Four
    Job38 Four

    I vote for the 1.9 easy access air box. Only three power steering mount brackets, I'd need at least a dozen attempts, good trick on gasket marker marking holes, What size wire you welding with, .035? I have learned one think watching your videos, how to bend steel by making long slits, thankyou for your videos from Maine USA.....

    • Donn DIY
      Donn DIY

      Cheers! I'm using 1 mm wire. It's 1/25 of an inch 😁 Bending that way is simpler. Needs welding though.

  • Will Wade
    Will Wade

    When I was in the Navy if a part was symmetrical we would CAD half of it then mirror it rather than CAD the whole part.

    • Donn DIY
      Donn DIY

      I know how to mirror part in SolidWorks, I haven't learned it in FreeCAD yet. 😁

  • ماجد المهندس
    ماجد المهندس

    ممتاز جدا 🌹⁦♥️⁩

  • Brian Morgan
    Brian Morgan

    Will this be better than your Tracked Amphibious Vehicle?

    • Brian Morgan
      Brian Morgan

      @Donn DIY thank you.

    • Donn DIY
      Donn DIY

      That will be a whole different vehicle. Can't compare them. I'll modify the tracked vehicle in the future and make more videos of it. Stay tuned for the future. 😉

  • paul martin
    paul martin

    Wow i can tell you like using the plasma table..... the brackets look really good too ! Cheers as always from Sydney Australia. 🇦🇺🐨🦘🇦🇺

    • Donn DIY
      Donn DIY

      I really do. It gives a professional look to the parts and once the blueprint is perfect it's repeatable any time. Can't do it that easy by hand. Cheers from Estonia. 😉💪

  • Charles de Voil
    Charles de Voil

    Flat panel air cleaner from a 4cyl toyota/hyundai? Boxes usually clamp together using the rubber edge of filter as a seal.

    • Donn DIY
      Donn DIY

      These do too, the filter acts as a seal.

  • Александр Барсуков
    Александр Барсуков

    👍👍👍👍👍👍👍👍👍👍👍👍

  • DIY Tech & Repairs
    DIY Tech & Repairs

    CNC plasma is something i would Love to have to. Makes it so much nicer building stuff. Should have had that building My super 7 :) Good progress

    • Donn DIY
      Donn DIY

      CNC plasma is really great. Makes life much easier. 😉

  • Роман Мальцев
    Роман Мальцев

    Красавчик!!!

  • Лука Павловић
    Лука Павловић

    pozdrav iz srbije

  • Philip Gevaert
    Philip Gevaert

    This is amazing !

    • Sebastien Lemay
      Sebastien Lemay

      @Philip Gevaert Estonia

    • Philip Gevaert
      Philip Gevaert

      @Donn DIY I love your DIY build ! You are lucky to have so much space available and a very well equiped work shop ! Very entertaining. Btw, where are you from ?

    • Donn DIY
      Donn DIY

      Thank you!

  • Nature's pleasure to relax
    Nature's pleasure to relax

    رائع رائع جميل

  • Альберт Смаков
    Альберт Смаков

    Двигателю другого места не нашлось?

    • Евгений Рындин
      Евгений Рындин

      Развесовка видимо

  • Colin Smith
    Colin Smith

    You should have kept the rubber mounts on the diffs otherwise you get driveline vibration, gear noise etc running through the chassis. This is why diffs are normally rubber mounted in all vehicles. Spider gears as well, because they are straight cut, will make odd sounds as you turn corners. I would highly recommend keeping the entire driveline mounted on rubber.

  • Виктор Наделяев
    Виктор Наделяев

    В каком регионе интересно кулибин?

    • Donn DIY
      Donn DIY

      Estonia.

  • temyra Verdana
    temyra Verdana

    The end of project is near! I am waiting to see on road test

  • Dr. Mark in Texas
    Dr. Mark in Texas

    🏆🏆🏆👍🙏 Thank you for sharing

    • Donn DIY
      Donn DIY

      Thank you for watching!

  • Сергей Прозоров
    Сергей Прозоров

    День добрый а ты по русский понимаешь?

  • Татьяна Ларионова
    Татьяна Ларионова

    Купи аккумуляторный гайковерт - ускорит процесс сборки (подгонки - когда нужно снять-поставить по несколько раз, откручивая\закручивая гайки\болты) деталей

Nästa
24K - 100
2:47
48tn
24K - 100
2:47
48tn